Matrix Games Forums

Now let’s look at the Microview Panel:



This is a condensed display of the map for the purpose of quick navigation around it. But, as in this case, even this level of condensement may not be enough to show the entire map.

A new feature of TOAW IV, however, solves that. Double-click inside the Micromap:





This brings up the Jump Map. The Jump Map is the same scale as the micromap, but shows the entire map (if there is space on your screen). Now you can jump to anywhere on the map by clicking where desired inside the Jump Map. Of course, this map was only a little larger than the max area of the Micromap, so scrolling the micromap might have worked better. But, the bigger the map gets the more useful the Jump Map becomes.

Here’s a shot from CFNA:



Now it’s starting to get really useful.

And here’s the Jump Map from World at War 1939-1945:



This one is so large that it even has to be scrolled to get to the entire map.

Finally, let’s look at the Button Panel:



Note the three tabs on the left side. The buttons are in three sections. The above shot shows the Units section.

Click on the Map tab. The Map section is shown:





Note that the Execute and Undo buttons are repeated on each section.

Click on the Reports tab. The Reports section is shown:



Note that, again, the Execute and Undo buttons are repeated on each section.

Now let’s look at the buttons themselves. Return to the Units tab. The first two buttons select the previous and next Units. The third button invokes the Unit Dialog:



New features are the scroll bar on the equipment list and the Unit icon display. There is also a new button to call up the OOB Report.

But there is another new feature when the unit is a ranged unit:



There is now a button to set the range.

Clicking on that button:





The range can now be set by the player. A positive value sets the range to that specific value. A value of -1 sets the range to the default value (maximum).

The main purpose of this feature is to tailor bomber ranges to keep them within range of any fighter escorting units. But it can also be used to limit a unit with multiple ranged equipment to the minimum range. Finally, it can be used to enable a ranged unit to assault instead of bombard, by setting the value to zero.

There is one more new feature, illustrated from this shot from Kaiserschlacht 1918 (Mini):



The designer can give a unit an “Alternate” icon. Here, the primary icon is the Special Forces icon (which gives a special ability to disengage automatically). But this unit also has an amphibious alternate icon (giving it a special ability to cross shallow water, marsh, and rivers, etc.). The two icons combine their special abilities. The primary icon is the one shown on the map. The alternate icon is only revealed in the Unit Report.

Finally, let’s look at the Unit Report for a naval unit:



Note that this unit has 10% damage (Damage is shown as 100 – damage). If the damage was 50% or greater, the button color would change to silver (for a bit of chrome).

Click on the equipment button:



The Equipment Report pops up. Note the new features: Shell weight is now shown for all ranged equipment. And naval parameters (Durability, Armor, Agility, Accuracy, and Speed) are now shown for all naval equipment. Note that Speed is shown both in kilometers per week and in knots.

The first two buttons on the second row of buttons on the Units Tab select the previous and next formations. The third button invokes the Formation Report:



There are several new buttons at the bottom. Two bring up the OOB – Units Report and the OOB – Formations Report. But the button on the left causes the formation to be moved by the PO. Actually, for that to take place, the button must be in “Hot” mode. It is shown here in “Safe” mode.

To go to “Hot” mode, PO Mode must be invoked. Exit the dialog and refer back to the Show Panels Panel in the upper left:

Toggle the left button until PO Mode is shown.



Note that the units now have a purple band across their Unit Values. This indicates that they will be controlled by the PO upon PO Execute.

Now run the Formation Report:



Note that the PO Move button is now shown in “Hot” mode. Clicking it will cause this formation to be moved by the PO.

Now go to the third row of the button panel and click the first button.



The OOB – Units Report is invoked. There are some new features: The Health Dot has been replaced with the Health Icon. The Unit Icon is included along with the Icon Type. There is now a scroll bar.

Next, click on the second button on that row:



The OOB – Formations dialog is invoked. This is a completely new dialog that was created specifically to aid in the control of the PO Assist feature. The check box controls whether the formation will be PO controlled.

Click on the 3rd Panzer Army check box:



Note that that formation is now under Manual Orders. It will not be controlled by the PO upon PO Execute.