Page 1 of 1

Newbie questions

Posted: Mon Oct 29, 2007 10:09 pm
by SMK-at-work
This is probably answered somewhere in the manual, but it's so much easier jsut to ask the assembled knowledge base [:)]

Is there a function to show which units report to a HQ?

RE: Newbie questions

Posted: Mon Oct 29, 2007 10:14 pm
by Banquet
If you change the colour of the HQ all it's subordinate units will also change colour. I only found that out yesterday and it's really helped me.


RE: Newbie questions

Posted: Mon Oct 29, 2007 10:14 pm
by darrellb9
The vertical colored bar on the left side of the units matches their HQ.

RE: Newbie questions

Posted: Mon Oct 29, 2007 11:29 pm
by TheHellPatrol
Yes, and every unit has its' HQ listed under its name...you can click on it and you'll be taken/scrolled right to the HQ[8D].

RE: Newbie questions

Posted: Mon Oct 29, 2007 11:43 pm
by Snoman
Bottom left of the screen is the statistics button.
One of the tabs in there is OOB.
This screen shows the complete layout of your chain of command, simplified so it doesn't fill the whole screen at once.

edit:

You can also jump to units from there.

RE: Newbie questions

Posted: Mon Oct 29, 2007 11:51 pm
by Erik Rutins
Excellent point, Snoman. The statistics screen is great and all the tabs are well worth checking out for new and experienced players.

RE: Newbie questions

Posted: Tue Oct 30, 2007 12:24 am
by SMK-at-work
Ah...hadn't spotted that - thanks! [&o]

RE: Newbie questions

Posted: Tue Oct 30, 2007 3:16 am
by Willburn
Can I throw in a newbie question too? How do I know if im loosing supply due to to the range it has to travel (from say location to primary hq.) Say if my location is 16 road squares (160 action points i assume for supply to move I assume?) from my primary hq, will it report somewhere that ive lost some % of my supply due to the range?

RE: Newbie questions

Posted: Tue Oct 30, 2007 3:27 am
by Snoman
Firstly, I think road squares count as 1 ap for supply transfers.
The best way to check would be to click on the unit the supply is coming from and then click the supply layer button (looks like a fuelcan).
If the subordinate unit is in the green, then there is no losses. (make sure you click on the next HQ down to check the supply from there. You will need to turn supply layer off then on again to refresh I think).

Alternately, look at the destination unit in question. On the left are the supply stats. If 'In' is less than 'Rqst' then it means either the higher HQ didn't have enough supply, or there is a distance penalty.

Finally, 16 road hexes will give no supply penalty. It counts as 16 AP, and the first level of penalty kicks in at 100 ap.

RE: Newbie questions

Posted: Tue Oct 30, 2007 8:43 am
by Vic
ORIGINAL: Willburn

Can I throw in a newbie question too? How do I know if im loosing supply due to to the range it has to travel (from say location to primary hq.) Say if my location is 16 road squares (160 action points i assume for supply to move I assume?) from my primary hq, will it report somewhere that ive lost some % of my supply due to the range?

hi willburn,

if production is concerned you will notice the location will accumulate left overs of production that could not be delivered.

as a general rule to check supply. you should select the HQ (where supply is going out from, or production has to be delivered too) and click the supply layer button. The color overlay in green means everything is ok. yellow =75%, blue=50%, red=25%, no color= 0 % supply or delivery

cheers,
vic


RE: Newbie questions

Posted: Tue Oct 30, 2007 12:55 pm
by Willburn
Thanks for all the usefull info :) Btw manual page 50 gives an impression supply uses 10 ap not 1. With that info bit (thanks snowman) I will be attacking much further ahead!

RE: Newbie questions

Posted: Tue Oct 30, 2007 2:12 pm
by darrellb9
Another useful thing to note is that with supply mode on if you mouse over a unit (or hex) it will show you in the info textbox what the AP cost is to that hex from the selected HQ so you can figure out roughly how much farther you can go before a unit starts to lose supply or where you may need to put in some roads or bridges for supply purposes.

RE: Newbie questions

Posted: Tue Oct 30, 2007 10:16 pm
by Willburn
Yikes that was really usefull thanks db99. I have another question. How far ahead from a hq can a unit be and still get the combat bonuses from the hq staff? Has it anything to do with the Staffcom value (100 for my german staff in my current scenario)

RE: Newbie questions

Posted: Tue Oct 30, 2007 11:12 pm
by Awac835
Willburn you can measure it pretty easy, I think it was within 4-5 hexes they get 100% then on they start lossing 20% with 0% bonus beyond 10 hexes.

Yeah i think it has something to do with some of the staff stats but not sure which. But its properly modable in the editor if you wanned to simulate modern times with modern communication.

RE: Newbie questions

Posted: Sat Nov 03, 2007 2:14 am
by Willburn
More newbie questions:
(edited post as ive found out a lot just by watching the combat sim)
Im left with a few more questions after trying to figure out how combat works:

(1) What is required for a unit to get the pinned result?
(2) is your chance to hit = total attack value / total defensive value. Anything at or above 1 = 100%

The reason I ask this question is that I cant get my head around the fact a tank attacking a infantery got: AFTER ALL MODS: Attval= 39.864, DefVal= 145. and killed the infantery, while in another battle a tank had the same number but missed the same type of unit. (40something vs 120 something)

The manual states that "When a soldier attacks another soldier, there is an Attack Points vs. Hit Points chance that it hits." this sentance seem to me to imply that as long as your attack points are higher than hit points you hit.

Or does it mean that you take the attack points devided them by the defence points and get the final chance to hit? (39,864/145=0.27 = 27% chance of kill.)

RE: Newbie questions

Posted: Sat Nov 03, 2007 2:18 am
by Willburn
one more (5) How does hide really work. If you have two different unit stacks 1 with scouts other with say tanks in one square. The enemy got enough scouting points to see your tanks, will both units be shown or will the enemy see only the tanks? How about if the scouts and the tanks is in the same stack, will the enemy see both the tanks and the scouts?