Page 1 of 1
Editor question
Posted: Tue Oct 30, 2007 11:52 am
by Jim D Burns
Is there any way to change the hex grid pattern in the editor? As it is the straight hex row runs north/south and east/west lacks a straight hex row. I was looking at porting some board game maps to the game but the hex rows don't match, it would be nice if we could tilt the rows as desired.
The entire Europa series has a straight hex row that runs east/west, so none of those maps are portable to the game without tilting true north.
Also can a map be shaved down after it is constructed? I was looking at a Europa map (Fire in the East and Scorched Earth combined) and came out to a count of 174 hexes north south and 116 hexes east west.
It would be great if I could just make a default 200x200 map, build it, then shave off the edges I don’t need. I would also like to shave out blocks of non-used areas, so not having to make every map a four sided only affair would be a great feature as well. Scorched Earth has a small map that juts out at the bottom near the Turkish border, but the rest of Turkey is not mapped, so I’d need to be able to shave out the Turkey area of the map.
Jim
RE: Editor question
Posted: Tue Oct 30, 2007 1:15 pm
by Vic
Hi Jim,
ORIGINAL: Jim D Burns
Is there any way to change the hex grid pattern in the editor? As it is the straight hex row runs north/south and east/west lacks a straight hex row. I was looking at porting some board game maps to the game but the hex rows don't match, it would be nice if we could tilt the rows as desired.
The entire Europa series has a straight hex row that runs east/west, so none of those maps are portable to the game without tilting true north.
I was not planning to implement this. It would be quite major a change and be quite a lot of work. but i'll give it some thought anyway.
Also can a map be shaved down after it is constructed? I was looking at a Europa map (Fire in the East and Scorched Earth combined) and came out to a count of 174 hexes north south and 116 hexes east west.
It would be great if I could just make a default 200x200 map, build it, then shave off the edges I don’t need. I would also like to shave out blocks of non-used areas, so not having to make every map a four sided only affair would be a great feature as well. Scorched Earth has a small map that juts out at the bottom near the Turkish border, but the rest of Turkey is not mapped, so I’d need to be able to shave out the Turkey area of the map.
Actually this can be done. You should create an extra landscapetype with a black hex as a graphic that does not allow movement in of any kind and use it to cut out areas of the map. Then also make a regime called something like "Offmap", put it to sleep stand and assign all the black hexes to this regime. If you make the color of the regime black then in the minimap its area will appear to be cut out too.
kind regards,
Vic
RE: Editor question
Posted: Tue Oct 30, 2007 1:18 pm
by tweber
You cannot change the hex orientation so it may be difficult to make an exact copy. Also, the hexes are slightly rectangular (53 by 48 pixels) so you have to take that into acocunt if you do not want the map to look slightly stretched. However, from a practicality standpoints, making a hex to hex copy of a 174 by 116 map is difficult without making errors anyway (over 20 k hexes to paint).
I think the best way to make maps is to use the map overlay feature and not worry if it is perfect copy of a paper board game (after all, the units will not be perfect copies). All you need is a picture of the area of interest and you can superimpose it on the hex grid. For maps, I like to use source data.
The US Military Academy's Depart of History publishes a wide range of military atlases. I like to use this instead of old game maps. Afterall, the old game map was probably adapted from an older source. When you copy an older game, you are making a copy of a copy. Google's Maps is also a great way to make generic geographical areas and get cities in the right relative location.
As to shaving down the map, you cannot do it. You could define an impassible hex and then use it to fill out the dead areas. If you look at the Pacific War Scenario, I blacken out Siberia because that area is not in play.
It might be better though to properly size your maps. The game file for large maps gets to be quite large and it may be difficult to mail around if you plan to do a lot of pbem.
RE: Editor question
Posted: Wed Oct 31, 2007 4:47 pm
by beserko
"I think the best way to make maps is to use the map overlay feature" where is this feature? The editor is leaveing me scratching my head. I have been useing the cyberboard system for years
http://cyberboard.brainiac.com/download.html I have plenty of maps I want to convert.[/align]The manual covering the editor is similiar to my idiots guide to nuklear fission!

[/align] [/align]

[/align]
RE: Editor question
Posted: Wed Oct 31, 2007 4:59 pm
by leastonh1
Ogre!!!! Wow, I haven't seen that great game for many a year. Crikey, that brings back fond memories! My beloved Amigas (500, 600, 1200). Ahhh, how I miss them. [:)]
RE: Editor question
Posted: Wed Oct 31, 2007 7:10 pm
by tweber
Go to the main editor menu. Select settings and look for the 'map overlay' button. A prompt will ask you for a picture file. The picture will be stretched over the hex grid so you have to take the picture dimensions and the hex dimensions (53 by 48) into account to avoid horizontal or vertical stretching. To do the picture above, you might have to define two land types (rock and lava) and an impassible river for the walls. Send me a pm if you are stuck
RE: Editor question
Posted: Wed Oct 31, 2007 9:39 pm
by freeboy
ogre oh my me too..