Page 1 of 1

Buddy laser process?

Posted: Mon Jul 14, 2014 9:54 pm
by ryszardsh
I am obviously inept but for the life of me I cannot figure out how to use the loadouts with the buddy laser requirement. I have tried multiple aircraft (e.g. A-6E) where each has a laser designator and I select active but no joy. I even tried putting a seal team equipped with a designator nearby and turning on the designator and no joy - are laser designators that fickle?

RAS

RE: Buddy laser process?

Posted: Mon Jul 14, 2014 10:39 pm
by RoryAndersonCDT

Harrier dropping paveway, hornet providing illumination
Image

Weapon needs to support buddy illumination Image

Weather could be effecting things [:D]

Plus make sure you are running command 1.04

RE: Buddy laser process?

Posted: Tue Jul 15, 2014 8:44 pm
by ryszardsh
I am running 1.04. Just rarely get the dashed red target line for a laser illumination. Never noticed but does it illuminate only upon bomb release? Maybe I was thinking laser works more like in real life where laser marks target and then bomb releases. I even tried telling a laser designator equipped unit to F1 attack the target to see if that would illuminate but no joy...

RAS

RE: Buddy laser process?

Posted: Tue Jul 15, 2014 9:35 pm
by mikmykWS
Could you please post a file showing this.

Thanks!

Mike

RE: Buddy laser process?

Posted: Wed Jul 16, 2014 12:14 am
by ryszardsh
file attached. 4 AV8-B mission assigned to hit a SA-6. Load is laser mavericks, never illuminates, never fires, just goes round and round the target....

RE: Buddy laser process?

Posted: Wed Jul 16, 2014 3:49 am
by Tomcat84
I'm pretty sure it illuminates after release only and it automatically uses the other unit's laser without you specifically having to tell it to do so. If there is no supporting unit to lase then you will get a message about no illumination available in the attack window. So if it says OK to release even though the unit does not have a laser, that means it will use the ground based or other aircraft based laser

(I think [:)] )

RE: Buddy laser process?

Posted: Wed Jul 16, 2014 1:22 pm
by ComDev
Hm yeah, I looked real quick and the AN/PAQ-1 set carried by the SEAL team is not in the AGM-65E Laser Maverick's 'legal directors' list. So its a database error, which means I scr*wed up. Have added a ticket on this. Will look into it when we start ramping up again late this summer / early fall.

I opened the scen you attached in the scenario editor and added a 'Inf Sec (Forward Air Controller [Laser Designator])' and the AV-8Bs immediately fired.

Sorry about that one, here have a virtual beer

RE: Buddy laser process?

Posted: Wed Jul 16, 2014 4:43 pm
by mikmykWS
Just fixed in the db as well. You'll see it next update.

Mike

RE: Buddy laser process?

Posted: Wed Jul 16, 2014 10:36 pm
by ryszardsh
well dang that solution is a surprise...so with multiple AV-8 in the strike package why did they not self illuminate - #1 illuminates for #2 etc?
RAS

RE: Buddy laser process?

Posted: Thu Jul 17, 2014 10:08 am
by ComDev
AV-8Bs were not fitted with laser illuminators [8D] It was not until very recently that they got targeting pods.

RE: Buddy laser process?

Posted: Thu Jul 17, 2014 8:18 pm
by ryszardsh
well that makes sense - and now I know better than to play the game w/o reading glasses on, cause I sure thought the AV-8B had a laser pod but after looking at the F9 options I see it is a LLTV and an IR capability, my bad:




Image