Pacific, Heroes and Leaders mod Expansion

Get ready for Mark H. Walker's Lock ‘n Load: Heroes of Stalingrad. This is the first complete computer game in the Lock ‘n Load series, covering the battles in and around Stalingrad during World War II.
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US M1 40L mm AA

This is the famous Bofors, which was the most widely used AA gun of the Second World War. 34,116 were built in the U.S. during WW2, and they served in all theaters in most of the same types of units as the M1A2. A light-weight, air transportable version known as the M5, which when disassembled could be carried in a C-47, was also built. In order to supply both the U.S. Army and U.S. Navy with much greater numbers of the guns, Chrysler built 60,000 of the guns and 120,000 barrels through the war, at half the original projected cost, and filling the Army's needs by 1943. Over the lifetime of the production, their engineers introduced numerous additional changes to improve mass production, eventually reducing the overall time needed to build a gun by half; most of these changes were in production methods rather than the design of the gun itself. York Safe & Lock also produced the weapons, though its attempts to coordinate drawings across the program were unsuccessful, and this responsibility was transferred to the Naval Gun Factory in July 1943.
Bofors also developed a towable carriage which they displayed in April 1935 at a show in Belgium. This mount allowed the gun to be fired from the carriage with no setup required, although with limited accuracy. If time was available for setup, the gunners used the tow-bar and muzzle lock as levers, raising the wheels off the ground and thereby lowering the gun onto supporting pads. Two additional legs folded out to the sides, and the platform was then leveled with hand cranks. The entire setup process could be completed in under a minute.
The gun fired a 900 g high explosive 40 × 311R (rimmed) shell at 900 m/s. The rate of fire was normally about 120 rounds per minute (2.0 rounds per second), which improved slightly when the barrels were closer to the horizon as gravity assisted the feeding from the top-mounted magazine. In practice firing rates were closer to 80–100 rpm (1.3–1.7 rounds per second), as the rounds were fed into the breech from four round clips which had to be replaced by hand. The maximum attainable ceiling was 7,200 m, but the practical maximum was about 3,800 m. The gun was provided with an advanced sighting system. The trainer and layer were both provided with reflector sights for aiming, while a third crew-member standing behind them "adjusted" for lead using a simple mechanical computer. Power for the sights was supplied from a 6V battery.
The first version of the 40 mm the Navy ordered was intended for use on submarines, where the larger calibre allowed the gun to be used for both AA and against smaller ships. The barrel was shorter at 42 calibers long, with the effect of reducing the muzzle velocity to about 700 m/s. When not in use, the gun was pointed directly up and retracted into a watertight cylinder. The only known submarines that used this arrangement was the Sjölejonet-class boats. The guns were later removed as the subs were modified with streamlined conning towers.
Although originally intended as an Airborne weapon it was mainly used in the PTO—presumably by the 101st, 102nd, and 843rd AAA Automatic Weapons Battalions (Air-Transportable). Eighteen U.S. Bofors were field-mounted on M3 halftracks by the 209th AAA Automatic Weapons Battalion (SP), and in 1945 were used by that unit in the ground support role on Luzon.

Image
Attachments
US M1 40L mm AA.jpg
US M1 40L mm AA.jpg (41.29 KiB) Viewed 1409 times
Semper fidelis
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US M1A1 75mm Howitzer

The M1 A1 75mm Pack Howitzer was designed in the 1920s to meet a need for a howitzer that could be moved across difficult terrain, as a mountain gun able to be disassembled and carried by pack mules. The gun and carriage were designed so that it could be broken down into several pieces to be carried by pack animals. The gun saw combat in World War II with the United States Army (primarily used by airborne units) and the United States Marine Corps. Due to meager funding, production rates were low; by 1940, only 91 pieces were manufactured. It was not until September 1940 that the howitzer was put into mass production. Production continued until December 1944.
Later a new carriage with pneumatic tires was introduced, thus making the gun able to be towed at higher speeds by a motorized vehicle (usually a Jeep) as well as enabling it to be dropped by parachute. In the latter role it was broken down into nine loads, which in 1944-45 were held together by a harness during their descent. (Prior to 1944 no harness was used, causing a wide dispersion of the gun's components and resulting in an average assembly time of half an hour in daylight or one hour at night.)
The howitzer M1 or M1A1 consisted of tube and breech, which were joined together by interrupted threads, allowing for quick assembly and disassembly. One eighth of a turn was required to connect or disconnect tube and breech. The tube had uniform, right hand rifling with one turn in 20 calibers. The breech was of horizontal sliding-block type, with continuous-pull firing mechanism. The recoil system was Hydro-pneumatic. Both recoil buffer and recuperator were located under the barrel.
The 75mm pack howitzer was used in action by field artillery battalions of Marine divisions (officially deleted in May 1945), airborne divisions, and the 10th Mountain Division in Italy. It was also used by several nondivisional artillery battalions in Europe, the Pacific islands, and Burma/China. Some also equipped regimental cannon companies in the PTO. Allied troops who used it included British airborne and Chinese artillery units, and Yugoslav partisans. In U.S. service a pack howitzer battery comprised four such weapons.
An airborne division, according to the organization of February 1944, had three 75 mm howitzer battalions – two glider field artillery battalions (two six-gun batteries each) and one parachute field artillery battalion (three four-gun batteries), in total 36 pieces per division.
The only mountain division formed, the 10th, had three 75 mm howitzer battalions, 12 pieces each. The gun was also used by some separate field artillery battalions. These included mule-packed field artillery battalions seeing service in Burma. In the US Marine Corps, 1943 divisional artillery included three 75 mm howitzer battalions, 12 pieces each.

Image
Attachments
US M1A1 75..Howitzer.jpg
US M1A1 75..Howitzer.jpg (41.62 KiB) Viewed 1409 times
Semper fidelis
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US M1A1 90L mm AA

The 90 mm gun M1/M2/M3 was an American heavy anti-aircraft and anti-tank gun, playing a role similar to the German 8.8cm Flak 18. It had a 90 mm diameter bore, and a 4.6 m barrel, giving it a 50 caliber length. It was capable of firing a 90 mm × 600 mm shell 19,042 m horizontally, or a maximum altitude of 13,300 m.
In 1940 the M1 90mm AA gun. A few hundred M1s were completed when several improvements were added to produce the 90 mm M1A1, which entered production in late 1940, and was accepted as the standard on May 22, 1941. The M1A1 included an improved mount and spring-rammer on the breech, with the result that firing rates went up, to 20 rounds per minute. Several thousand were available when the US entered the war, and the M1A1 was their standard anti-aircraft gun for the rest of the conflict. Production rates continued to improve, topping out in the low thousands per month. By the end of 1942 more than 2,000 90mm AA guns had been built, and they saw service in all theaters. Two deficiencies of the 3-in. AA gun which were not corrected in the 90mm piece were the amount of time required for unlimbering and the inability to depress the gun barrel to fire on targets at lower elevations. This was due to their having been designed solely for AA fire, with little consideration given to use against ground targets.
Even as the M1A1 gun was entering production it was decided that AA guns should be able to fire at all types of ground targets as well as aircraft. On September 11, 1942, the Army issued specifications for a new mount to allow it to be used in this role, which resulted in the 90 mm M2, introducing yet another new mount that could be depressed to 10 degrees below the horizontal and featured a new electrically-assisted rammer. It became the standard weapon from May 13, 1943. The M1A1 was redesigned to incorporate this principle, resulting in the M2 in 1943. In the M2 the gun itself was little changed, but the mount was entirely new and provided for both rapid unlimbering and limbered fire. Because of the M2's ability to fire at land, sea, and air targets it came to be known as the "triple threat" gun. By the end of the war 7,831 M1, M 1A1, and M2 90mm AA guns had been built.
The M3 gun was used on the M36 tank destroyer, and the T26 (later, M26) Pershing tank. The M3 fired an M82 APC shot with a muzzle velocity of 810 m/s. However, both the muzzle velocity of the standard M3 gun and the quality of the steel used in the M82 APC (armor-piercing capped) shot, while comparable to the 8.8 cm KwK 36 L/56 mounted on the Tiger I, were inferior to the Tiger II's KwK 43 L/71 8.8 cm main gun firing its standard APCBC (armor-piercing capped ballistic cap) shot used by German forces, with the result that the former's penetration fell far short of the standard projectile fired by that German tank.
They were used in four-gun batteries in both Mobile and Semimobile AAA Gun battalions, and also in those types of units previously equipped with 3-in. AA guns. Until mid 1943 one four-gun 90mm (or 3-in.) AA battery was also included in the Special Weapons battalion of a Marine division.

Image
Attachments
US M1A1 90L mm AA.jpg
US M1A1 90L mm AA.jpg (48.2 KiB) Viewed 1409 times
Semper fidelis
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US M1A2 37L mm AA

Coming out of the experience gained in the First World War, the United States sought to develop a large-caliber gun for use in aircraft. The Baldwin 37mm automatic gun was considered, but ultimately rejected. The famous John Browning was called upon in 1920 to look at this matter, and by 1924 he developed two 37mm prototypes for testing at Aberdeen Proving Ground. He developed two types given the U.S. Army had also developed a requirement for a lightweight 37mm gun for air defense against ground attack aircraft. The final version did not enter production until 1939. It compared unfavorably with the 40rnm AA gun in several respects but, since production of the latter could not meet demands, the M1A2 continued to be built.
The anti-aircraft gun fired a 21-ounce explosive shell at a rate of fire of 120 rounds per minute. The effective altitude it could fire up to was 10,500 feet – the shell was fitted with a self-destruct mechanism set for this altitude. It could also be used against ground targets, with a maximum range of 8,850 yards (though the self-destruct mechanism would detonate after 4,000 yards of horizontal flight).
The 37 mm M9 auto-cannon was a derivative of the M1A2 anti-aircraft gun. It had a 74-inch barrel, weighed 405 pounds (the barrel alone weighing 120 pounds), had a muzzle velocity of 3,000 feet per second, and had a rate of fire of 150 rounds per minute. 7,278 were manufactured and the gun saw service in all theaters throughout the war. It was also employed as the MA of the M15 and M15A1 MGMC halftracks. Two gun units were coupled to the M5 gun director using the M1 remote control system. The system was powered by the M5 generating unit. If the remote system was inoperative the M5 sighting system was used. In addition to the towed variant, the gun was mounted, with two M2 machine guns, on the M2/M3 half-track, resulting in the T28/T28E1/M15/M15A1 series of multiple gun motor carriages.
The Army used the M1A2 in four-gun batteries in both Mobile and Semimobile AAA (Anti-Aircraft Artillery) Automatic Weapons battalions, and in Coast Artillery (AA) regiments. It was used on PT boats around 1944 in the Pacific theater during World War II, replacing the M4 auto-cannon. The Marines used four-gun M1A2 platoons in AAA battalions, Defense battalions, and divisional Special Weapons battalions.
In early World War II, each Army Anti-Aircraft Artillery (AAA) Auto-Weapons battalion was authorized a total of thirty-two 37 mm guns in its four firing batteries, plus other weapons. During World War II the 37 mm gun M1 was deployed in coast defense anti-motor torpedo boat batteries (AMTB) alongside 90 mm guns, usually four 90 mm and two 37 mm guns per battery. Some AMTB batteries consisted of four 37 mm guns, but most sources have little information on these batteries. In the later part of the war the 37 mm gun was typically replaced by the 40 mm Bofors gun M1.

Image
Attachments
US M1A2 37L mm AA.jpg
US M1A2 37L mm AA.jpg (41.3 KiB) Viewed 1409 times
Semper fidelis
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US M2A1 105mm Howitzer

After World War I, the U.S. Army Ordnance Department studied various captured German 105 mm-caliber howitzers and developed the 105 mm Howitzer M1920 on Carriage M1920. A box trail carriage design (the M1925E carriage) and two other split trail designs (the T1 and T2) were also developed, but the original split trail design was found superior after testing. After being selected, the piece was standardized in December 1927 as the 105 mm howitzer M1 on carriage M1. The Army had an intention to replace all 75 mm gun-howitzers in its divisional and non-divisional field artillery regiments with 105 mm pieces, but a lack of appropriations stalled the idea and eventually forced it to be completely abandoned by 1929; a limited plan developed in 1925 envisioned re-equipping three regiments, but by 1933, only 14 M1 howitzers had been manufactured.
A modified version of the M1 was trialed in 1932 which used semi-fixed ammunition instead of separate-loading ammunition. Since this development required a different breech block, the new piece was designated the 105 mm howitzer M2 on carriage M1. 48 pieces were manufactured in 1939. The original M1 carriage had been designed for towing using horses rather than trucks, and a new carriage, the T5 (M2), was developed in 1939 and standardized in February 1940. The breech ring of the howitzer M2 was modified in March 1940 before large-scale production began, creating the 105 mm howitzer M2A1 on carriage M2. The weapon was heavy for its calibre but this was because the gun was designed to be durable. Thus the barrel and carriage could see great use and remain functional without wearing out.
As the standard divisional light artillery piece, the M2A1 was used in the field artillery battalions of Marine, cavalry, and infantry divisions, and also in nondivisional field artillery battalions. A battery consisted of four howitzers, each towed by a 272-ton truck. 8,536 were built by the end of the war. 13 different types of ammunition were developed for it.
The M2A1 was an excellent howitzer and in various modified forms is still in service with over forty countries, including the U.S. where it is designated the M101A1. The U.S. military artillery designation system was changed in 1962, redesignating the M2A1 howitzer the M101A1. The gun continued to see service in the Korean and Vietnam Wars. Though a similar model, the M102 howitzer, shared the same roles in battle, it never fully replaced the M101A1. Today, the M101A1 has been retired by the U.S. military, though it continues to see service with many other countries. By the end of the Second World War, 8,536 105 mm towed howitzers had been built and post-war production continued at Rock Island Arsenal until 1953, by which time 10,202 had been built.

Image
Attachments
US M2A1 10..Howitzer.jpg
US M2A1 10..Howitzer.jpg (39.2 KiB) Viewed 1409 times
Semper fidelis
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US M3 3in 76L mm AA

The 3-inch anti-aircraft gun M3 was an anti-aircraft gun developed from the earlier 3-inch M1917 and 3-inch M1918 guns which served throughout the 1930s, some into early World War II. By the time of the US entry into World War II, the 3-inch M3 was in the process of being replaced and may have seen action in the Pacific during World War II.
During the late 1920s, M1917 and M1918 guns were fitted with removable barrel liners and re-designated as 3-inch M1, M2, or M3 guns, depending on the variant they were upgraded from. The most numerous variant was the M3 which was introduced in 1928 and consisted of a new barrel with a removable autofretted liner. During the 1930s further upgrades were proposed but these were abandoned with the adoption of the 90 mm gun M1 in 1938.
The M3 consisted of a 76.2 mm (3 in) barrel 50 calibers in length, which had a removable liner and a semi-automatic vertical sliding-wedge breech. The barrel had a hydro-pneumatic recoil system and when fired the breech ejected the shell casing and remained open until a new round was loaded. The M2A2 cruciform carriage had a circular center section and four perforated steel outriggers for stability. For transport, the outriggers folded and a two-wheeled, single axle bogie could be screwed onto the outriggers at each end. The carriage had pneumatic tires, electric brakes and was capable of being towed at high speeds. The gun was provided with a set of equilibrators and was capable of both high angle fire +80° and 360° of traverse.
There were two distinct types of 3-in guns. AA guns: a mobile version (which the game piece represents), and a static gun that was used in permanent defenses. About 800 were built. In September 1940 a project started to adapt the 3-inch gun to the anti-tank role, starting with the T9 experimental model but equipping it with the breech, recoil system and carriage borrowed from the 105mm M2 howitzer. The gun was accepted for service as the 3-inch M5.
By 1941 most had been relegated to training roles, but some equipped Coast Artillery (AA) regiments and Marine Defense battalions in the PTO where they saw combat during the initial Japanese attacks (e.g., on Guam, Wake Island, and in the Philippines). AP ammunition was not issued to the static guns.
One interesting fact concerning all Army AA units is that prior to March 1942 they were part of the Coast Artillery; hence they had Coast Artillery designations until inactivated or renamed later in the war. A 3-in. AA battery comprised four guns.
A similar derivative of the T9 – the 3-inch M6 – was intended to be mounted on the M5 self-propelled gun, which was eventually abandoned. A final adaptation was the 3-inch M7, which included minor modifications for mounting on the M6 heavy tank and M10 tank destroyer. The M7 saw wide use although it was supplanted to some extent by more powerful weapons such as the 90mm M3 and the British QF 17 pounder. A total of 6,824 M7 guns were manufactured.

Image
Attachments
US M3 3in 76L mm AA.jpg
US M3 3in 76L mm AA.jpg (33.42 KiB) Viewed 1409 times
Semper fidelis
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US M4A1 Halftrack 81mm Mortar

M2 Halftrack Car was modified in October 1941 to be able to transport the mortar of 81 mm M1 in the back compartment. This new model was indicated M4 81 mm Mortar Motor Carriage (MMC). M4 MMC was assigned to HQ companies of the armoured battalions of infantry and tanks. To accomodate the mortar, the seats to the back were removed and replaced by racks of ammunition being able to accomodate 96 projectiles. The mortar was directed backwards but could not be used inside the vehicle and especially not moving (except in the event of urgency). To be used, the mortar was descended from the vehicle and was posed on the ground. With this intention a door of access was installed to the back, the rail for machine-guns of M2 however was preserved. M4 was standardized in October 1940 and 572 specimens were produced by White Motor Co in 1942.
The M4A1 Mortar Carrier Halftrack, like the M3 Gun Motor Carriage, is a rare derivative of the original M2 Halftrack. The M4 version was developed to meet the need for a self-propelled artillery piece that could be unloaded at the battlefield. Most crews in practice rarely unloaded the gun, instead firing it while in its rear-facing position The M4A1 turned the gun around and reinforced the vehicle, allowing for more convenient firing. The M4 Mortar Carrier was based on the M2 Halftrack and arose from the desire to increase the mobility of the medium, mortar and its crew in mechanized units. Unfortunately, since it was assumed that the mortar would always be dismounted before being fired, the mounting faced to the rear and had an extremely limited traverse. 572 were built. The M4A1 Halftrack 81mm was a redesign of the M4 Mortar Carrier. In it the mortar still faced to the rear, but was provided with increased traverse and a reinforced mount to absorb the shock of recoil when firing.
One thought to M3 to transport the mortar of 81 mm towards the end 1942, but as the project did not advance, one used as bases the M2A1. This new model was baptized M4A1 81 mm Mortar Motor Carriage. Contrary to M4, the M4A1 could use its mortar from the interior and in move because of the reinforcement of the mounting of the mortar and the floor of Halftrack. The M4A1 was easily recognizable thanks to the trunks of arrangement assembled to the back on each side of the door of access the M4A1 standardized in December 1942 was produced to 600 specimens by White in 1943.

Image
Attachments
US M4A1 Ha..m Mortar.jpg
US M4A1 Ha..m Mortar.jpg (47.73 KiB) Viewed 1409 times
Semper fidelis
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US M5 3 inch 76L mm ATG

In 1940, the US Army just started to receive its first anti-tank gun, the 37 mm gun M3. While it fit the request of the Infantry for light, easy to manhandle anti-tank weapon, Artillery and Ordnance foresaw a need for a more powerful gun. This led to a number of expedient designs, such as adaptations of the 75 mm M1897 or towed variants of the 75 mm M3.
While the M1 57mm AT gun was being developed in 1941, the Army also decided to start work on a more powerful weapon. To bring it into production as quickly as possible, the designers used the barrel of the 3-in. (76mm) AA gun and the carriage, breech, and recoil mechanisms of the 105mm howitzer. The result was rather large and heavy for an AT gun (its weight in action was almost twice that of the German 7.5cm PaK 40), but it worked better than might have been expected from such an improvisation.
The barrel was adapted from the 3 inch Gun T9; it had rifling with a uniform right hand twist, with 28 grooves and one turn in 25 inches. Barrel length was 13.16 feet. It was combined with breech, recoil system and carriage from the 105 mm Howitzer M2. The breech was of horizontal sliding type, manual; the recoil system hydro-pneumatic. The carriage was of split trail type, equipped with a single equilibrator spring beneath the breech and wheels with pneumatic tires. While the M3 3-in. AA gun and the M7 3-in., gun of the M10 GMC had semiautomatic breech blocks, the M5 had a manual breech block which lowered its rate of fire. Production began in December 1942. 2,500 were built before production ended in 1944.
A towed TD battalion possessed 36 pieces, in three companies of 12. M3 Halftracks were issued as prime movers. The organization from 1 September 1944 authorized M39 Armored Utility Vehicle instead, but these only reached the frontline in spring 1945.
Those towed tank destroyer battalions were attached to US Army divisions to improve their anti-tank capabilities. Most often, a complete battalion was attached to an infantry division. In some cases, towed TD battalions were attached to armored or airborne divisions; sometimes, companies of the same battalion were given to different divisions; and sometimes a single division had several TD battalions - including a mix between towed and self-propelled - at once. In early 1945 most towed battalions were converted to SP, making the towed gun relatively rare in the last few months of the war. In addition to the anti-tank role, the gun was often used to supplement divisional field artillery or to provide direct fire against enemy fortifications (e.g. a combat report from the 614th TD mentioned a two-gun section firing 143 shells at an enemy post, achieving 139 hits).
In October 1943, the first towed battalion - the 805th, - arrived in Italy. Subsequently, the M5 saw combat in the Italian Campaign and in the Northwest Europe. The greatest test of the TD battalions and their M5 guns came during the Battle of the Bulge. In this battle, towed tank destroyers fought much less successfully and suffered much higher losses than the self-propelled ones. Apparently it was not used in the PTO.

Image
Attachments
US M5 3in 76L mm ATG.jpg
US M5 3in 76L mm ATG.jpg (30.6 KiB) Viewed 1409 times
Semper fidelis
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US M21 Halftrack 81mm Mortar

While the "rear-fire only" characteristic of the halftrack mortar carriers enabled them to make a rapid withdrawal from an untenable position, it also meant that they took longer to get into firing position—which made them unpopular with their crews when going into action under fire. Consequently the M21 Mortar Carrier, based on the M3 Halftrack, was designed with a forward-facing mortar.
Unlike the M4 mortar carriage, which was based on the M2 Half Track Car, the M21 was based on the M3 Half-track with a longer and roomier rear. The vehicle was 6.32 m long, 2.22 m wide, and 2.26 m high with a wheelbase of 3.44 m. The suspension for the front wheels were leaf springs and track's suspension used a vertical volute spring. Powered by a White 160AX, 128 hp (95 kW), 6,330 cc, 6-cylinder petrol engine with a compression ratio of 6.3:1, the M21 could reach up to 72 km/h on a road. The fuel capacity was 230 l and the vehicle had a range of 240 km. It had a power-to-weight ratio of 15.8 hp/ton with the vehicle weighing nine tons. To allow the use of the mortar in the compartment of combat, the mounting of the weapon was reinforced, as well as the floor of the vehicle. Important fact, the 81 mm M1 mortar was not directed any more backwards but forwards. vehicle and could now swivel of 30° on each side.
Armament was supplemented by a .50cal machine-gun (12.7 mm) air-cooled M2HB assembled on pedestal. It was produced by the White Motor Company in 1944. Only 110 examples were produced.
The M21 had a different layout from the early M4 and M4A1 MMC, as it was the replacement of the M4. The major difference, was that the M21 and the M4 were based on different half-tracks (the M4 was based on the M2 Half-track while the M21 was based on the M3 Half-track). The major difference was the location and direction of the mortar (the M4's mortar was rear-facing and was near the back, while the M21's mortar was front-facing and was closer to the front).
The M21 served on the Western Front, seeing action in Normandy and in southern France, before later being used during the Battle of the Bulge, the Battle of Belgium, Operation Market Garden, and the invasion of Germany from the west. Apparently none were used in the PTO.
Standard US tank and armored infantry battalions had a mortar platoon equipped with either M21s or the older M4 MMCs. The M21 was used mainly to illuminate targets at night or provide indirect fire support to the infantry. The M21 served with the US 3rd, 1st, and 7th Armies during the campaign in France, and the 2nd Armored Division, which developed it. In addition, 57 examples were leased to Free French forces. By 1945, it was declared obsolete, due to the insufficient power of the 81 mm mortar as an artillery piece.

Image
Attachments
US M21 Hal..m Mortar.jpg
US M21 Hal..m Mortar.jpg (48.3 KiB) Viewed 1409 times
Semper fidelis
GiveWarAchance
Posts: 538
Joined: Tue Feb 10, 2015 10:42 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by GiveWarAchance »

Those halftracks look very chunky and delightful.
I was wondering how it would be like to turn backwards to fire at the enemy.

oh ya and Merry Christmas to the tiny community here.[font="Microsoft Sans Serif"][/font]
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

I wish you a ....

Image
Attachments
I wish you a.jpg
I wish you a.jpg (187.71 KiB) Viewed 1411 times
Semper fidelis
GiveWarAchance
Posts: 538
Joined: Tue Feb 10, 2015 10:42 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by GiveWarAchance »

That looks like a giant swimming pool.
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US M51 4x.50 cal MG AA

In order to develop a mobile anti-aircraft weapon, several 0.5 inch (12.7 mm) twin machine gun mounts were tested on the chassis of the M2 half-track including Bendix, Martin Aircraft Company, and Maxson. The Maxson M33 turret mount was preferred and—on the larger M3 half-track (T1E2)—and was accepted for service in 1942 as the M13 Multiple Gun Motor Carriage.
During World War II, the M45 turret was mounted on two specific systems; the M16 Multiple Gun Motor Carriage and the M51 Multiple Machine Gun Carriage. When mounted on the M20 trailer, it was known as the M55 Machine Gun Trailer Mount, but this system had not finished testing before the cessation of hostilities. M51s were withdrawn from service by the end of World War II in favor of the M55. This weapon was the same as that on the M16 MGMC halftrack, but here was mounted on a four-wheel trailer. In both cases the weapons system was usually referred to as the Maxson, after its manufacturer. A lighter air-transportable version was also developed; designated the M55, it could be towed by a Jeep.
The M51 4x.50 cal MG AA was developed by the W. L. Maxson Corporation to replace the earlier M33 twin mount (also from Maxson). Although designed as an anti-aircraft weapon, it was also used against ground targets. Introduced in 1943 during World War II, this weapon was operated by two loaders and one gunner. The mount is capable of traversing a full 360 degrees around, with an angle elevation between -10 and +90 degrees. Traverse and elevation are electrically driven, powered by two rechargeable 6-volt batteries. All four guns could be fired at once, but standard practice was to alternate between firing the upper and lower pair of guns, allowing one pair to cool while the other was in use. This allowed for longer periods of action as overheating of the gun barrels was lessened. The "tombstone" model M2 ammunition chests held 200 rounds each—with one ammunition chest on an M45 system holding ten times as many rounds as each of the four twenty-round 20mm magazines of the German Flakvierling system held (and which, on the German ordnance system, had to be changed every six seconds on each gun of the quartet to ensure its own top 800 rpm "combined" firing rate), with each M2 ammo chest weighing 89 pounds each when full.
Was the principal weapon (along with the 37mm gun) of highly mobile anti-aircraft artillery battalions deployed in the European Theater during World War II. These battalions provided invaluable air defense to much larger units, particularly field artillery. The Quadmount .50 caliber served as a very strong deterrent to strafing runs by enemy warplanes as, in addition to their gross firepower, its quartet of Browning M2HB "heavy barrel" .50 caliber guns were capable of being "tuned" to converge upon a single point at distances which could be reset while in use. Multiple-gun mounts were developed for the M2 Browning because the M2's rate of fire (450–550 rounds per minute) for a single gun was too low for anti-aircraft use. It was also tested by the US Navy as a solution for the Kamikaze attacks that started in late 1944. Two Essex class aircraft carriers received six mounts each for operational testing starting with CV-16 Lexington in May 1945. Her gunnery department in general was positive towards the powered mounts but felt that the guns were too light and ineffective against the high speeds that the diving Kamikaze aircraft possessed.

Image
Attachments
US M51 4x...al MG AA.jpg
US M51 4x...al MG AA.jpg (41.67 KiB) Viewed 1411 times
Semper fidelis
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US T25 155mm Mortar

The American Army did field heavier calibres mortars, up to 155mm, which could fire a bomb weighing 601bs out to ranges of more than 2,200 yards. They also had a 4.2in (107mm) M2 mortar with a rifled barrel, which was served by specially-raised Chemical Warfare Service units to provide a smokescreen. From 1943, they were provided with a high explosive round to greatly improve their utility. As such, then, this weapon along with the 105mm T13 and 155mm T25 mortars, were not standard issue to weapons companies within an infantry battalion, but were employed by separate units to provide additional fire support.
The T25 155 mm mortar (155mm Mortar T25) is a muzzle-loading heavy mortar made in the United States. Development began at about the same time as the 105mm mortar T13, and the larger T25 was also produced. This weapon was designed to give heavy and immediate fire support to amphibious landings and jungle troops in locales not suited to conventional artillery. To be moved, it had to be disassembled; the tube and recoil mechanism were loaded aboard a special handcart, while a second cart carried the bipod and baseplate. Other carts transported the ammo, with six rounds on each. Combat trials were conducted in the SW Pacific in 1944. Only 244 were built.
It was deployed to the heavy weapons unit of the amphibious unit operating on the Southwestern Pacific Front in 1944, and although it had the advantage of great power due to the size of the shell, it was a very large and heavy weapon, so it not was quick. It was difficult to move, and although modifications such as self-propelled guns were made, it eventually disappeared.

Image
Attachments
US T25 155mm Mortar.jpg
US T25 155mm Mortar.jpg (39.11 KiB) Viewed 1411 times
Semper fidelis
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

HaL American Availability Artillery and Team catalog

Image
Attachments
HaL Americ.. catalog.gif
HaL Americ.. catalog.gif (141.88 KiB) Viewed 1411 times
Semper fidelis
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US Bazooka M1A1

Bazooka is the common name for a man-portable recoilless anti-tank rocket launcher weapon, widely deployed by the United States Army. Also referred to as the "Stovepipe", the innovative bazooka was among the first generation of rocket-propelled anti-tank weapons used in infantry combat. Featuring a solid-propellant rocket for propulsion, it allowed for high-explosive anti-tank (HEAT) warheads to be delivered against armored vehicles, machine gun nests, and fortified bunkers at ranges beyond that of a standard thrown grenade or mine.
Shaped charge technology was developed in the US into a shaped charge hand grenade for use by infantry, effective at defeating up to 60 mm of vehicle armor. The combination of rocket motor and shaped charge warhead would lead to Army development of light antitank weapons.
In 1942, U.S. Army Colonel Leslie Skinner received the M10 shaped-charge grenade which was capable of stopping German tanks. He gave Lieutenant Edward Uhl the task of creating a delivery system for the grenade. Uhl created a small rocket, but needed to protect the firer from the rocket exhaust and aim the weapon.
By late 1942, the improved Rocket Launcher, M1A1 was introduced. The forward hand grip was deleted, and the design simplified. The production M1A1 was 1.37 m long and weighed only 5.8 kg.
The ammunition for the original M1 launcher was the M6, which was notoriously unreliable. The M6 was improved and designated M6A1, and the new ammunition was issued with the improved M1A1 launcher. After the M6, several alternative warheads were introduced. Many older M1 launchers were modified to M1A1 standards in July and August 1943, with batches of M6 rockets also being modified with the latest ignition systems to be able to be fired from the modified M1 launchers; these rockets were designated M6A2. The M6A3 rocket featured a blunt, rounded nose to lessen the chances of it ricocheting off of angled armor, and was meant to be fired from the M9, and later M9A1, launchers. Late in World War II, the M6A4 and M6A5 rockets with improved fuses were developed.
The original M1 and M1A1 rocket launchers were equipped with simple fixed sights and used a launch tube without reinforcements. During the war, the M1A1 received a number of running modifications. The battery specification was changed to a larger, standard battery cell size, resulting in complaints of batteries getting stuck in the wood shoulder rest (the compartment was later reamed out to accommodate the larger cells). The M1 and M1A1 used a rear iron sight and a front rectangular "ladder" sight positioned at the muzzle. The vertical sides of the ladder sight were inscribed with graduations of 100, 200, 300, and 400 yards, with the user elevating the bazooka so the rear sight lined up with the selected "rung" on the front sight. On the M9, the ladder sight was replaced by the General Electric T43 aperture sight. Ranging was accomplished by looking through the rear sight's peep hole while rotating the assembly (which had graduations of 100, 200, and 300 yards) so it lined up with the blade positioned at the muzzle. In September 1944, during the production of the M9A1, the T43 sight was replaced by the Polaroid T90 optical reflector sight, which used an etched reticle for aiming. The T43 and T90 sights were interchangeable. Various types of blast deflectors were tried, and an additional strap iron shoulder brace was fitted to the M9 launcher.

Image
Attachments
US Bazooka M1A1.jpg
US Bazooka M1A1.jpg (31.66 KiB) Viewed 1411 times
Semper fidelis
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US Bazooka M9A1

In 1943, field reports of rockets sticking and prematurely detonating in M1A1 launch tubes were received by Army Ordnance at Ogden Arsenal and other production facilities. At the US Army's Aberdeen Proving Grounds, various metal collars and wire wrapping were used on the sheet metal launch tube in an effort to reinforce it. However, reports of premature detonation continued until the development of bore slug test gauges to ensure that the rocket did not catch inside the launch tube.
The original M6 and M6A1 rockets used in the M1 and M1A1 launchers had a pointed nose, which was found to cause deflection from the target at low impact angles. In late 1943, another rocket type was adopted, the M6A3, for use with the newly standardized M9 rocket launcher. The M6A3 was 493 mm long, and weighed 1.53 kg. It had a blunted, more round nose to improve target effect at low angles, and a new circular fin assembly to improve flight stability. The M6A3 was capable of penetrating 89–102 mm of armor plate.
Battery problems in the early bazookas eventually resulted in replacement of the battery-powered ignition system with a magneto sparker system operated through the trigger. A trigger safety was incorporated into the design that isolated the magneto, preventing misfires that could occur when the trigger was released and the stored charge prematurely fired the rocket. The final major change was the division of the launch tube into two discrete sections, with bayonet-joint attachments. This was done to make the weapon more convenient to carry, particularly for use by airborne forces. The final two-piece launcher was standardized as the M9A1. In September 1944, the fragile folding aperture sight was replaced by a Polaroid optical reflector sight. However, the long list of incorporated modifications increased the launcher's tube length to 1.55 m, with an overall empty weight of 6.5 kg. From its original conception as a relatively light, handy, and disposable weapon, the final M9A1 launcher had become a heavy, clumsy, and relatively complex piece of equipment.
In October 1944, after receiving reports of inadequate combat effect of the M1A1 and M9 launchers and their M6A1 rockets, and after examining captured examples of the German 8.8 cm RPzB 43 and RPzB 54 Panzerschreck, the US Ordnance Corps began development on a new, more powerful anti-tank rocket launcher, the 90 mm M20.
In 1945, the U.S. Army's Chemical Warfare Service standardized improved chemical warfare rockets intended for the new M9 and M9A1 launchers, adopting the M26 Gas Rocket, a cyanogen chloride (CK)-filled warhead for the 2.36-in rocket launcher. CK, a deadly blood agent, was capable of penetrating the protective filter barriers in some gas masks, and was seen as an effective agent against Japanese forces (particularly those hiding in caves or bunkers), whose gas masks lacked the impregnants that would provide protection against the chemical reaction of CK. While stockpiled in US inventory, the CK rocket was never deployed or issued to combat personnel.

Image
Attachments
US Bazooka M9A1.jpg
US Bazooka M9A1.jpg (30.21 KiB) Viewed 1411 times
Semper fidelis
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US Browning M2HB (0.5)

The M2 machine gun or Browning .50 caliber machine gun is a heavy machine gun designed toward the end of World War I by John Browning. The M2 uses the much larger and much more powerful .50 BMG cartridge, which was developed alongside and takes its name from the gun itself (BMG standing for Browning machine gun). The Browning M2 is an air-cooled, belt-fed machine gun. The M2 fires from a closed bolt, operated on the short recoil principle. The M2 fires the .50 BMG cartridge, which offers long range, accuracy, and immense stopping power. The closed bolt firing cycle made the M2 usable as a synchronized machine gun on aircraft before and during World War II, as on the early versions of the Curtiss P-40 fighter.
The M2 has varying cyclic rates of fire, depending on the model. The M2HB (heavy barrel) air-cooled ground gun has a cyclical rate of 450–575 rounds per minute. The early M2 water-cooled AA guns had a cyclical rate of around 450–600 rpm. The AN/M2 aircraft gun has a cyclic rate of 750–850 rpm; this increases to 1,200 rpm for AN/M3 aircraft guns. These maximum rates of fire are generally not achieved in use, as sustained fire at that rate will wear out the bore within a few thousand rounds, necessitating replacement. In addition to full automatic, the M2HB can be selected to fire single-shots or at less than 40 rounds per minute, or rapid fire for more than 40 rounds per minute. Slow and rapid firing modes use 5–7 round bursts with different lengths of pause between bursts.
The M2 has an effective range of 1,830 metres and a maximum effective range of 2,000 metres when fired from the M3 tripod. In its ground-portable, crew-served role as the M2HB, the gun itself weighs 38 kg and the assembled M3 tripod another 20 kg. In this configuration, the V-shaped "butterfly" trigger is located at the very rear of the weapon with a "spade handle" hand-grip on either side of it and the bolt release in the center. The spade handles are gripped and the butterfly trigger is depressed with one or both thumbs.
When the bolt release is locked down by the bolt latch release lock on the buffer tube sleeve, the gun functions in fully automatic mode. Conversely, the bolt release can be unlocked into the up position resulting in single-shot firing (the gunner must press the bolt latch release to send the bolt forward). Troops in the field have been known to add an improvised safety measure against accidental firing by slipping an expended shell casing under the butterfly trigger. The upgraded M2A1 has a manual trigger block safety.
Because the M2 was designed to operate in many configurations, it can be adapted to feed from the left or right side of the weapon by exchanging the belt-holding pawls, and the front and rear cartridge stops (three-piece set to include link stripper), then reversing the bolt switch. The operator must also convert the top-cover belt feed slide assembly from left to right hand feed as well as the spring and plunger in the feed arm. This will take a well trained individual less than two minutes to perform.
The charging assembly may be changed from left to right hand charge. A right hand charging handle spring, lock wire, and a little "know-how" are all that are required to accomplish this. The M2 can be battle-ready and easily interchanged if it is preemptively fitted with a retracting slide assembly on both sides of the weapon system. This eliminates the need to have the weapon removed from service to accomplish this task.

Image
Attachments
US Brownin..HB (0.5).jpg
US Brownin..HB (0.5).jpg (29.62 KiB) Viewed 1411 times
Semper fidelis
User avatar
asl3d
Posts: 12499
Joined: Mon Feb 06, 2017 4:48 pm

RE: Pacific, Heroes and Leaders mod Expansion

Post by asl3d »

US Browning M1918A2 (0.3)

The Browning Automatic Rifle (BAR) is a family of American automatic rifles and machine guns used by the United States and numerous other countries during the 20th century. The primary variant of the BAR series was the M1918, chambered for the .30-06 Springfield rifle cartridge and designed by John Browning in 1917 for the American Expeditionary Forces in Europe as a replacement for the French-made Chauchat and M1909 Benét–Mercié machine guns that US forces had previously been issued.
The BAR was designed to be carried by infantrymen during an assault advance while supported by the sling over the shoulder, or to be fired from the hip. This is a concept called "walking fire"—thought to be necessary for the individual soldier during trench warfare. The BAR never entirely lived up to the original hopes of the war department as either a rifle or a machine gun.
The U.S. Army, in practice, used the BAR as a light machine gun, often fired from a bipod (introduced on models after 1938). A variant of the original M1918 BAR, the Colt Monitor Machine Rifle, remains the lightest production automatic firearm chambered for the .30-06 Springfield cartridge, though the limited capacity of its standard 20-round magazine tended to hamper its utility in that role.
Final development of the M1918A2 was authorized on 30 June 1938. The FN-designed pistol grip and rate-reducer mechanism with two rates of automatic fire was shelved in favor of a rate-reducer mechanism designed by Springfield Armory, and housed in the butt stock. The Springfield Armory rate reducer also provided two selectable rates of fully automatic fire only, activated by engaging the selector toggle. Additionally, a skid-footed bipod was fitted to the muzzle end of the barrel, magazine guides were added to the front of the trigger guard, the hand guard was shortened, a heat shield was added to help the cooling process, a small separate stock rest (monopod) was included for attachment to the butt and the weapon's role was changed to that of a squad light machine gun. The BAR's rear sight scales were also modified to accommodate the newly standardized M2 ball ammunition with its lighter, flat-base bullet. The M1918A2's walnut butt stock is approximately one inch longer than the M1918 BAR's butt stock. The M1918A2's barrel was also fitted with a new flash suppressor and fully adjustable iron sights. Late in the war a barrel-mounted carrying handle was added.
In 1942 a shortage of black walnut for butt stocks and grips led to the development of a black plastic butt stock for the BAR. Composed of a mixture of Bakelite and Resinox, and impregnated with shredded fabric, the stocks were sandblasted to reduce glare. The Firestone Rubber and Latex Products Co. produced the plastic butt stock for the US Army, which was formally adopted on March 21, 1942.

Image
Attachments
US Brownin..A2 (0.3).jpg
US Brownin..A2 (0.3).jpg (28.48 KiB) Viewed 1411 times
Semper fidelis
dox44
Posts: 653
Joined: Sun May 07, 2000 8:00 am
Location: the woodlands, texas

RE: Pacific, Heroes and Leaders mod Expansion

Post by dox44 »

Camp Geiger and Jacksonville NC...two blasts from the past.

2nd Radio Battalion 76-78
Post Reply

Return to “Lock ‘n Load: Heroes of Stalingrad”