How to read the Event Log properly

Gary Grigsby’s War in the East: The German-Soviet War 1941-1945 is a turn-based World War II strategy game stretching across the entire Eastern Front. Gamers can engage in an epic campaign, including division-sized battles with realistic and historical terrain, weather, orders of battle, logistics and combat results.

The critically and fan-acclaimed Eastern Front mega-game Gary Grigsby’s War in the East just got bigger and better with Gary Grigsby’s War in the East: Don to the Danube! This expansion to the award-winning War in the East comes with a wide array of later war scenarios ranging from short but intense 6 turn bouts like the Battle for Kharkov (1942) to immense 37-turn engagements taking place across multiple nations like Drama on the Danube (Summer 1944 – Spring 1945).

Moderators: Joel Billings, elmo3, Sabre21

User avatar
morvael
Posts: 11763
Joined: Fri Sep 08, 2006 9:19 am
Location: Poland

RE: How to read the Event Log properly

Post by morvael »

Some men are taken from the pool outside of replacement phase, for example when squads are delivered to partisan units via air drops. That's why they are not accounted for in the USED column, and thus POOL-USED does not equal to ACTIVE (this info is dumped at different time - the very end of logistics phase).

TRANSFER is transfer pool, these men are returning from the front, and will make it to ACTIVE pool at the start of your next logistics phase (so there is a week delay, men returning are not available to be used in the same turn). Your TRANSFER is mostly made of those men listed in the BACK column in replacement phase (but there may be some men returned outside of replacements phases). Default production screen view shows numbers for ACTIVE+TRANSFER thus giving false impression that you have unused men in the pool. It can be switched to show either ACTIVE or TRANSFER (or both).

WilliSaenger
Posts: 50
Joined: Wed May 11, 2016 1:09 pm

RE: How to read the Event Log properly

Post by WilliSaenger »

ok, thank you
User avatar
MrBlizzard
Posts: 636
Joined: Mon Apr 16, 2012 7:34 pm
Location: Italy

RE: How to read the Event Log properly

Post by MrBlizzard »

One question:
Why ready elements go from front to transfer pool and then they go back to the pool?
What is it modeling?
Blizzard
User avatar
morvael
Posts: 11763
Joined: Fri Sep 08, 2006 9:19 am
Location: Poland

RE: How to read the Event Log properly

Post by morvael »

Time to dispatch them to new owners. It's a simplification and averaging of time spent away from the front. For some elements it could mean servicing, replacing some used up parts etc. It is also helpful in replacement procedures not going crazy with items appearing in the pool magically mid-phase and throwing distribution calculations off.
Nix77
Posts: 565
Joined: Sun Oct 02, 2016 6:19 am
Location: Finland

RE: How to read the Event Log properly

Post by Nix77 »

ORIGINAL: morvael

HQ has TOE%/1000 chance to add 1 to leader admin skill. That's why I prefer to keep mine up to strength.


Is this stated somewhere in the rules?

Here's a direct quote from the rules 11.3.1 Leader Rating Check Procedure
Approximately one admin point is subtracted from the leader's admin rating for every ten percent the HQ unit is below its TOE support squad strength, with a max reduction of five points.

Which one is correct, or do they both apply?

In any case, I'd keep my HQ ToE above 90% when possible :)
User avatar
morvael
Posts: 11763
Joined: Fri Sep 08, 2006 9:19 am
Location: Poland

RE: How to read the Event Log properly

Post by morvael »

Only the chance to add +1 applies.
Nix77
Posts: 565
Joined: Sun Oct 02, 2016 6:19 am
Location: Finland

RE: How to read the Event Log properly

Post by Nix77 »

ORIGINAL: morvael

Only the chance to add +1 applies.

Are you 100% sure about that? I can only find the penalty from the manual, and no signs of +1 chance either in the manual or patch notes?
User avatar
morvael
Posts: 11763
Joined: Fri Sep 08, 2006 9:19 am
Location: Poland

RE: How to read the Event Log properly

Post by morvael »

I'm sure, I have written down detailed rules for leader rolls in a post some time ago.
Manual is very badly outdated.
User avatar
EwaldvonKleist
Posts: 2412
Joined: Thu Apr 14, 2016 3:58 pm
Location: Berlin, Germany

RE: How to read the Event Log properly

Post by EwaldvonKleist »

Anyone has a link to this? In which section morvael?
User avatar
morvael
Posts: 11763
Joined: Fri Sep 08, 2006 9:19 am
Location: Poland

RE: How to read the Event Log properly

Post by morvael »

Search is not working on the dev forum. I can't find it, and I don't have time for manual search [:(]
User avatar
morvael
Posts: 11763
Joined: Fri Sep 08, 2006 9:19 am
Location: Poland

RE: How to read the Event Log properly

Post by morvael »

Found this via Google:
fb.asp?m=3761599
May be a bit outdated, but only slightly, in edge cases.
User avatar
EwaldvonKleist
Posts: 2412
Joined: Thu Apr 14, 2016 3:58 pm
Location: Berlin, Germany

RE: How to read the Event Log properly

Post by EwaldvonKleist »

Thank you very much morvael[&o]
Nix77
Posts: 565
Joined: Sun Oct 02, 2016 6:19 am
Location: Finland

RE: How to read the Event Log properly

Post by Nix77 »

There's quite many differences to the manual there, stuff that's not even in the condensed manual I think? I wish there was a REAL updated manual [:(]
Post Reply

Return to “Gary Grigsby's War in the East Series”